Setting Standards Program PABX Panasonic TDA using Telephone

This article describes a quick way to program the PABX Panasonic TDA type using Digital Key Telephone . But this method is not recommended for setting up the program if a lot of features to be programmed , because the programming mode using the Digital Key Telephone , many of the features or settings that can not use a telephone line in the program , you should use UPCMC or software to program the type of Panasonic PABX TDA . preparation : Reset the PABX . This is useful so that all values ​​of the program back to the default value or the default value . How to reset : Raise the switch on the MPR card toward the Initialize System . Turn on the PABX . After a few seconds , put the switch in the direction of Normal PABX is ready to be programmed with a factory default value , this will allow us to start the program . Starting program : Aircraft digital telophone first plug in the jack / port first , the TDA 100D , no extentionnya 101 . If using Digital Card ( DLC , DHLC , etc. ) there is always a first port position . Go to the program menu : [ Program ] [ * # 1234 ] Then enter the code number , on the telephone , to enter into the program code must press [ Enter] , being the [ Sp - Phone ] were used to going to the menu selanjutnya.Jika no one program , no need to press the [ Hold ] to return to the home menu , simply press the [ Cancel ] , the sub menu will be returned to the appropriate program code of the program being dipakai.Setting TRS level : [ 301 ] [Enter ] to enter [ Level No. : browse 2 ] [ Location No. : 001 contents ] [ contents with a value of 00 ] [ Enter] and [ Sp - Phone ] to move to [ Location No. 002 : content 100 ] [ Enter] [ Cancel ] [ Cancel ] No Level Up screen display . [ Level No. : fill 3 ] [ Location No. : 001 contents ] [ contents with value 0 ] [ Enter] [ Location No. 002 : content 100 ] [ Enter] [ Cancel ] [ Cancel ] [ Level No. : browse 4 ] [ Location No. : 001 contents ] [ contents with nial : 00 ] [ Enter] [ Sp - Phone ] [ 01 ] [ Enter] [ Sp - Phone ] [ 02 ] [ Enter] [ Sp - Phone ] [ 03 ] [ Enter] [ Sp - Phone ] [ 04 ] [ Enter] [ Sp - Phone ] [ 05 ] [ Enter] [ Sp - Phone ] [ 06 ] [ Enter] [ Sp - Phone ] [ 07 ] [ Enter] [ Sp - Phone ] [ 0809 ] [ Enter] [ Sp - Phone ] [ 09 ] [ Enter] [ Cancel ] [ Cancel ] [ Level No. : browse 5 ] [ Location no: 001 ] [ fill in the values ​​: 1 ] [ Enter] [ Sp - Phone ] [ 2 ] [ Enter] [ Sp - Phone ] [ 3 ] [ Enter] [ Sp - Phone ] [ 4 ] [ Enter] [ Sp - Phone ] [ 5 ] [ Enter] [ Sp - Phone ] [ 6 ] [ Enter] [ Sp - Phone ] [ 7 ] [ Enter] [ Sp - Phone ] [ 8 ] [ Enter] [ Sp - Phone ] [ 9 ] [ Enter] [ Sp - Phone ] [ 0 ] [ Enter] Press the [ Hold ] to return to the menu system program . Description : If this setting has been completed , it will form a standard value COS 1 = Free Call Out COS 2 = Can DLD , CellPhone , Local , can not SLI COS 3 = Can only Local COS 4 = Can only Mobile COS 5 = Only intercom , could not call out . Programming : For a complete list of program code can be seen in the list of program code TDA Setting Line / Trunk installed : At TDA , the amount that can be attached tergantug line of cards , there are 8 , 16 , or 24 , but not all of the line used . Depending on the number line that we can from the provider ( Telkom numbers , gsm , and so forth ) . If the line is there is no such ONLY 4 , then the rest ( 5-6-7-8 ) we have to turn off or Out Of Service , so as not drawn a blank line when going to call out . How: Admission to the program [ 400 ] [ Enter] [ places Card Slot No. installed CO ] [ Port No. : Fill unused port ] select using the [Auto Ans ] until the display screen [ No Download ] [ Enter] Press the [ Sp - Phone ] or the [ Down Arrow ] to move to the next port . Repeat until all unused ports didiskonek of PABX . Setting Ring : For this ring setting , by default , though not in the program will ring at extension 101 . If you want to change it then it can be programmed in [ 450 ] The format is : [ 450 ] [ Enter] [ Time ] [ Slot No. ] [ Port No. ] [ Destination No. ] [ Enter] Description : [ Time ] = 1/2/3/4 Mode 1 for Day , 2 for Lunch mode , 3 for Break Mode , 4 for Night Mode . Default settings are not automatic mode , only Day Mode . [ Slot No. ] = 01 to 10 This no slots , depending on where the card is installed in CO PABX . [ Port NO ] = 01 to 16 Port where installation of the line from the outside . If there are only 4 line and installed sequentially , then the program enough to port 4 . [ Destination No. ] = Number Extension / ICD / OGM / Group etc. . It is the purpose of the line in port ring attached . If there is only one operator , then simply enter the no extension operator in [ Destination No. ] . Setting COS / restrict / restriction penelponan : To set an extension restrictions could call out , then it could be in the program at no program code [ 602 ] . The format is : [ 602 ] [ Enter] [ No Extension which will be restricted ] [ COS No. ] [ Enter] Description : [ COS No. ] as previously above information : The contents of 1 to 5 according to the facilities provided in the earlier extension . Setting Password : If there are some aircraft that locked access to call out , but could use a password to perform penelponan out , then it could be in 2 places in the program , ie no code [ 120 ] and code [ 122 ] The format is : [ 120 ] [ Enter] [ Location No. ] [ Verified Code ] [ Enter] for the program no: [ 122 ] [ Enter] [ Location No. ] [ PIN ] [ Enter] Description : [ Location No. ] is the password in place , the password or serial number . If we want to make for example the password 123456 , then the programming should be split into 2 , eg 123 and 456 . [ 120 ] [ Enter] [ 001 ] [ 123 ] [ Enter] [ 122 ] [ Enter] [ 001 ] [ 456 ] [ Enter] Eg would create 567 890 password : [ 120 ] [ Enter] [ 002 ] [ 567 ] [ Enter] [ 122 ] [ Enter] [ 002 ] [ 890 ] [ Enter] This is a simple program using a digital telephone , for standard features that are often used . Read more : http://suryawardana.com/pabx/cara-setting-standar-program-pabx-panasonic-tda-menggunakan-telephone/#ixzz2tBdXhK87