Wednesday, May 27, 2015

Setting way TDA100D

This article describes how to SETTING PROGRAM Panasonic PABX type TDA with Digital Telephone KX-DT333 SERIES OR KX-T7630.

Preparation:
Reset PABX.It is useful so that all the settings of the program back to default so that features running properly.
How to reset it: Raise switch on MPR card toward PABX System Initialize and wait 10detikkan turn off and turn on the PABX. After a few seconds, lowering switch in the direction of Normal, PABX is ready to be programmed with a factory default, this will allow us to start the program.
Program start:
The digital telophone aircraft jack plug in the first / first port on Digital card (if the card is in the slot Digital to 2 means dikonek to the first port in slot 2, the TDA 100D.
Go to the menu program:


[Program] [* # 1234]Then enter the code number of the program, on the telephone, to enter into the program code must press ENTER, Sp-Phone button being used more for heading selanjutnya.Jika menu there is a program, do not need to press the HOLD button to return to the original menu , simply press the CANCEL button will return to the program menu directory of program code that is being used.
Setting TRS level:

301 [Enter] to enterLevel No: 2 contents 2Fill with01: 00 Enter* Above code to restrict answering with prefix 00 (SLI prohibited, while DLD, HP, LOCAL allowed)2x press Enter phone screen there Posts Level No. (Fill with 3 then press enter)
Level No. 3 contents 3Fill with01: 01 Press Enter + SP-PHONE02: 02 Press Enter + SP-PHONE03: 03 Press Enter + SP-PHONE04: 04 Press Enter + SP-PHONE05: 05 Press Enter + SP-PHONE06: 06 Press Enter + SP-PHONE07: 07 Press Enter + SP-PHONE08: 09 Press Enter + SP-PHONE09: 080 Press Enter* Above code to restrict answering with prefix 08 (SLI and DLD prohibited, while HP, LOCAL allowed)2x press Enter phone screen there Posts Level No. (Fill in 4)
Level No: 4 contents 4Fill with:01: 0 Press Enter* Above code to restrict dialing prefix 0 (Only LOCAL allowed)2x press Enter phone screen there Posts Level No. (Fill in the 5 then press enter)
Level No: 5isi 5Fill with:01: 1 SP-PHONE + Enter02: 2 Enter + SP-PHONE03: 3 Enter + SP-PHONE04: 4 Enter + SP-PHONE05: 5 Enter + SP-PHONE06: 6 Enter + SP-PHONE07: 7 Enter + SP-PHONE08: 8 Enter + SP-PHONE09: 9 Enter + SP-PHONE10: * Enter + SP-PHONE11: # Enter* Above code to restrict dialing prefix 1-2 (Block)Press the [Hold] to return to the menu system program.
Specification:If this setting has been completed, it will form a standard valueCOS 1 = Free Calling OutCOS 2 = Could DLD, Mobile, Local, can not SLICOS 3 = Only can LocallyCOS 4 = Just get MobileCOS 5 = Only intercom, could not call out.Programming:For a complete list of program code can be found in the list of program code TDA
Setting Line / Trunk attached:In the TDA, the amount of line that can be installed depending on the card, there are 8, 16, but not all line port is used. Depending on the number line that we can from the provider (telecom number, GSM, etc.).If the line is there is no such ONLY 6, then the rest (7-8) should we turn off or Out of Service, in order not drawn a blank line when going to call out.Here's how:Admission to the program










[400] [Enter] [Slot No. installed a CO Card] [Port Number: Fill unused port] select using the [Auto Ans] to display the screen [No Connect] [Enter]Press [Sp-Phone] or the [Down] to move to the next port.Repeat until all unused ports didiskonek of PABX.

No comments:

Post a Comment